How To Choose Wood Flooring?
There are endless products available so please talk to a wood flooring professional to make a fully informed decision. Here are some starting points.
Dimensions & Manufacturing The wood flooring industry is completely separate from the tile industry and also from the carpet industry (which includes carpet, vinyl, and laminate). The hardwood flooring of the past 100 years was produced in standard dimensions of 3/4" thick face with widths of 1 1/2", 2 1/4", 3" or 3 1/4", 4", and 5". Now you can get plank flooring that's even wider in one inch increments. These products have been around for decades and they will be for many more decades. This makes them a good choice for a long term product.
Where and how the wood flooring is made can greatly influence the quality of the product. There are so many variables that a supplier and installer must know to match the customer with the right product. The following factors affect the product: lumber grading that goes into making the flooring grades, kiln drying schedules, regional color differences, range of board lengths, average board lengths, milling tolerances, grading percentage that is allowable but out of specification, number of mineral streaks, number of knots, speed of milling and total production process, storage of lumber and milled flooring, and shipping environment. There is so much to know that it takes a lot of experience to consistently supply good products.
Location The moisture fluctuation and the type of substrate/subfloor determine the type of flooring needed. Solid wood is the best value and the most widely used, but it reacts to moisture the most. Most people prefer solid products whenever possible, since they are more durable and longer lasting. If moisture is a concern or radiant heat or concrete substrates are involved, then engineered flooring or rift & quartersawn (R/Q) solid flooring must be used. Engineered wood is assembled from a thin layer of hardwood and a plywood backing for increased stability during moisture fluctuations. R/Q flooring has more vertical grain so the flooring boards only change width about half as much as standard, plainsawn boards. These are the wood flooring options, but many mention laminate flooring in the same catagory even though it is particle board with a picture laminated onto the top. So laminate is not wood flooring.
Finishing Hardwood floors can be prefinished or site-finished. Site-finished flooring is installed and then sanded and finished. With a full sanding after installation these floors are completely smooth once they're finished. Now days all prefinished flooring is milled with a bevel on the board edge so an installed floor has grooves between the boards. The prefinished products is UV cured so the finish is harder than site finished product. But usually prefinished surfaces are too hard to adhere new finish during a recoat. Also prefinished product is available only in certain woods, grades, and colors specific to that manufacturer.
With prefinished you get higher durability finish, flooring that's likely not recoatable, a few less product options, bevels between the boards, less overall installation time.
With site finished flooring you get unlimited wood, grading, color, and sheen options, slightly less durable finish that's not UV cured, finish that is recoatable, smooth floor with no bevels, a day or two longer total time for the sanding and finishing process.
Hardness This is an important consideration. The required hardness is determined by the traffic that the floor will see. Heavy daily use, children, and dogs require a wood that is at least as hard as red oak. Heavy traffic on a floor requires a harder wood such as Cumaru, Brazilian Cherry, Brazilian Walnut, Hickory, Maple, or Oak.
Grade & Color The grade and color of the wood can give a contemporary, traditional, or rustic feel to the area. The color is determined by the species and the finish. This should compliment or blend with the surrounding woodwork, walls, and furniture. The layout, whether it is strip, plank, or parquet flooring, and the use of medallions and borders all affect the style and feel as well.
Summary Solid, site finished flooring is the most popular for numerous reasons. It is recoatable. After 5 to 10 years the surface may become worn, and it only needs to be buffed and coated. It is customizeable. It can be stained any color and finished in any sheen. It is easily cleaned, since it has a smooth surface. It is readily available. A wide range of woods have been available for decades and will continue to be. Medallions and borders are easily created. Solid wood can be refinished numerous times.